![]() Step 6 – Repeat steps 3-5 until the stains are completely gone. Step 5 – Use a clean cloth and rinse out the sink with warm water. Step 4 – Spread the paste over the sink and let it sit for about a half hour. When you combine the two it will start to bubble. Step 3 – Make a thick paste with baking soda and vinegar. This will create a paste for you to use to scrub the sink. ![]() Step 2 – Sprinkle baking soda over the sink and then add a little bit of water. Step 1 – Clean your sink with warm water and a clean cloth to get any loose dirt and grime off. Follow these steps to clean your cast iron utility sink. Your sink will shine after this step! If you need to replace your stainless steel sink, check out these options.Ĭast iron sinks are easy to clean, but you have to be careful about scratching.ĭon’t use wire brushes, but make sure all your cleaning tools are gentle and that you don’t scrub too hard when you’re cleaning your sink. Step 5 – Put a small amount of olive oil on a clean microfiber cloth and rub down the whole sink. Step 4 – Rinse the sink with water and dry with a microfiber cloth. When the vinegar mixes with the baking soda it will create some bubbling. Step 3 – Sprinkle vinegar all over your sink to disinfect. ![]() Step 2 – Spread the paste all over the sink and let it sit for a few minutes. Baking soda is an abrasive cleaner and will give your stainless steel sink a beautiful shine. Step 1 – Create a paste using baking soda and water. Follow these steps to clean your stainless steel utility sink. You’ll find stainless steel sinks often in laundry rooms or mudrooms because they hold up well and look great when maintained. Stainless steel sinks look beautiful when they are clean, but terrible when they are dirty. If you need to replace your fiberglass sink, check out these options. Let it sit for 15 minutes and then drain. Step 8 – Fill the sink with warm soapy water using dish soap. Step 7 – Use a clean cloth and wipe down the sink and rinse with warm water. Step 6 – Cover the sink with a thin coat of the paste and let it sit for around 10 minutes. Add the vinegar slowly and keep mixing until you create a paste. Step 5 – Mix 1/4 cup of baking soda and 1/3 cup of vinegar. Step 4 – Scrub the paste off with a soft-bristled scrub brush or a toothbrush. If the stain isn’t gone, then apply more of the paste and let it sit for another 10 minutes. Step 3 – Cover the stains with the paste and leave it on there for around 10 minutes. You don’t have to use the whole amount of juice for the mixture. Add the juice slowly until it creates a paste. Step 2 – Mix 1/4 cup of borax (use rubber gloves to protect your hands!) and 1/4 a cup of lemon juice. Step 1 – Scrub your sink with a sink cleaner to get any loose dirt and grime off. Make sure you only use a soft bristled brush when cleaning this type of sink! Follow these steps to clean your fiberglass utility sink. However, they can often get scratched if you use certain products and tools. If you need to replace your plastic sink, check out these options.įiberglass utility sinks are often used in laundry rooms and basements because they are very durable. Let the soapy water sit for around a half hour and then drain the sink. Step 7 – Fill the sink with hot water and add enough dish soap to create some suds. Step 6 – Rinse the sink and if you still see a hint of any stains, then spray it again with the vinegar and water solution and let it sit for several hours. Spread the paste over the areas and let it sit for at least a half hour. Step 5 – If the stains persist, create a paste by mixing one part water, one part vinegar and one part baking soda. If the stains are gone, then skip down to Step 7. If you still have stains, move on to Step 5. Step 4 – Scrub the sink again and see if the baking soda helped to lift the stains. Step 3 – If there are still stains that aren’t coming out, sprinkle baking soda over them and then spray the sink again with the vinegar solution. Step 2 – Use a scrub brush and gently scrub the sink. Spray the entire sink and let it sit for at least 10 minutes. Step 1 – Pour 1 cup of water and 1/4 a cup of vinegar into a spray bottle. Follow these steps to clean your plastic utility sink. Since these sinks are durable, it makes them fairly easy to clean and it responds well to household cleaners, like vinegar. These sinks are also durable, which is why you find them in laundry rooms, garages, and mudrooms. Especially if you rinse your paint brushes in them! ![]() Plastic utility sinks are typically white, which make them easy to stain. The list goes on and on.Īfter a while, utility sinks can look pretty rough.įollow these step by step instructions on how to clean your utility sink and have it looking just like new! Plastic Utility Sink Paint from paint brushes, mud from dirty kids clothes, lint from the washer. Utility sinks get all kinds of things poured into them. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |